Based in Danbury, CT · Serving Connecticut & Nearby New York

California Redwood Siding: Facts, Care Tips and a Greenwich, CT Stain Project

By DaVince Painting · November 19, 2026 · Project Spotlight

California redwood is one of the most distinctive sidings a house can wear: warm color, straight grain, and a reputation for holding up outdoors. We recently sanded the California redwood siding on a home in Greenwich, Connecticut, and applied a premium PPG stain. The photos are further down. First, a closer look at this wood — where it comes from, why it still needs a finish, and how to work with it carefully.

Where redwood comes from, and why builders still use it

Coast redwood (Sequoia sempervirens), also called California redwood, is native to a narrow coastal fog belt from the far southwest corner of Oregon to Monterey County, California.

The darker, reddish-brown heartwood contains natural extractives, including tannins, that help it resist decay and insects. The cream-colored sapwood, closer to the bark, does not. In redwood grading, names with the word “Heart” are heartwood grades, recommended for use on or near soil. Builders also choose redwood because it is dimensionally stable: it shrinks, swells, and warps less than many other woods. Those defenses help older homes stay sound, but they are not a substitute for a finish.

Why unfinished redwood turns gray

Tannins cannot stop the sun. Ultraviolet light breaks down lignin at the wood’s surface. Rain then washes away the degraded material and the colored extractives, and unfinished redwood weathers toward a silver-gray. Mildew can add to that dull, blotchy look, even when the boards underneath are still sound. In Connecticut and nearby New York, a full year of sun, rain, snow, and freeze-thaw cycles speeds that wear. A protective stain will not make the siding maintenance-free, but it does slow fading and gives the wood a barrier against moisture and UV.

Tannins, fasteners, and stains you do not want

The same extractives can also stain the wood. When iron meets those tannins in the presence of moisture — from ordinary steel nails or screws, a wire brush, steel wool, or even a hammer face — the reaction leaves a blue-black or gray discoloration. Stainless-steel fasteners are the most reliable choice; high-quality hot-dipped galvanized or other coated fasteners are a common alternative. Do not clean redwood with steel wool or a wire brush.

Water can also dissolve the extractives and carry a yellow to reddish-brown stain through paint or a solid-color stain, especially a water-based topcoat. If you plan to paint redwood, prime first with a stain-blocking primer, often oil-based or alkyd. A penetrating stain, like the one on this Greenwich house, is a different kind of finish, but the same chemistry matters if you ever paint the siding later.

Care on the job: cleaning, drying, sanding, and safety

A finish can only perform as well as the surface it sits on. Clean with a wood cleaner, and a brightener when tannin or iron stains are present, then rinse thoroughly. High-pressure washing can tear soft surface fibers and drive water into the wall, so a brush and a hose — or a pressure washer kept on a low setting — is safer.

Then let the wood dry. Penetrating stain soaks into the pores. If those pores are full of water, the stain cannot penetrate, and moisture can be sealed into the siding. After a wash, wait for dry weather; do not stain wet boards. Sanding opens the pores, knocks down raised grain, and removes weak, weathered fibers so the color goes on evenly. A small test patch in an out-of-the-way spot shows the true color before the whole house is coated.

Work safely. Sanding makes dust that can irritate the eyes, skin, and lungs. Use a dust mask or respirator, wear gloves when you handle cleaners and finishes, and keep the area ventilated. Keep iron tools off wet redwood so you do not leave new stains behind.

Before and after: a Greenwich redwood home

On this Greenwich home, we sanded the California redwood siding and applied a premium PPG stain. The photos below show three sides of the same house, before and after that work.

Before: weathered, faded California redwood siding on the back of a home in Greenwich, CT, seen from the pool terrace

Before

After: California redwood siding on the back of the same Greenwich, CT home after sanding and a premium PPG stain, with the pool covered

After

Before and after at the back of the house, by the pool. The California redwood siding had faded to a dull, uneven brown. After sanding and a premium PPG stain, the color is warmer and more even, and the grain is easier to see. The pool is open in the before photo and covered in the after.
Before: faded vertical California redwood boards along the long side wall of a Greenwich, CT home

Before

After: the long side wall and corner of the same Greenwich, CT home, with California redwood siding freshly sanded and stained

After

Before and after on the long side wall. The vertical redwood boards looked dry and washed out in the sun. The after photo is taken from a slightly wider angle, at the corner of the house, and shows a more even color along the siding.
Before: weathered angled California redwood siding on the gable end of a Greenwich, CT home, with pool equipment at the foundation

Before

After: the same gable end after sanding and a premium PPG stain, with a richer, more even reddish-brown color in the redwood

After

Before and after on the gable end. The angled redwood boards had weathered unevenly, with some areas darker than others. The new stain evened out the color while still letting the grain show through.

Keeping redwood looking good

A fresh stain is not a one-time fix. Walls that get the most sun usually need attention first. How soon depends on exposure, the condition of the wood, and how well the surface was prepared. One simple check is to sprinkle a few drops of water on the siding: if it soaks in instead of beading, the finish is no longer shedding moisture as well as it should. We would rather walk a property and tell you what we see than give a generic timeline. If you are replacing boards, look for FSC-certified redwood, or consider reclaimed redwood from older structures.

If you have redwood or other wood siding in Connecticut or nearby New York that is starting to fade, gray, or look dry, the first question is usually about prep: what does the surface need before a new finish goes on?

Have redwood or other wood siding that needs attention?

DaVince Painting is based in Danbury, CT, and serves Connecticut and nearby New York. We'll take a look and give you an honest, free estimate — no pressure.

Request a Free Estimate

Planning a painting project?

Get a free, no-pressure estimate from a local painting contractor you can trust.